Share to FB

Speedometer Recalibration Unit

Starting in 1994, the factory started using electronic speedos on some of the models. Today, all models use this. If you are changing the transmission pulley, rear wheel pulley, rear tire or installing one of our transmissions, you will need a recal box. 

  • 95E-56B fits 1987-2006 Big Twin (except 2006 Dyna)
  • 95E-07-A fits 2006-Later Dyna and 2007-Later Softail/Touring models

Instructions for 95E-56B: Click Here

Instructions for 95E-07-A: Click Here

TERMS AND CONDITIONS

BAKER Drivetrain reserves the right to change prices, terms or policies at any time without notice. Orders can be pre-paid using Visa, MasterCard, American Express, Discover or PayPal. All orders not pre-paid will be sent C.O.D. certified check or money order only unless pre-approved for company check acceptance. Any orders from outside the USA must be pre-paid in US funds via wire transfer; a $30 transfer fee will apply. Prices shown are F.O.B. Haslett, MI.

LIMITED WARRANTY POLICY

BAKER™ transmission assemblies and transmission builder 's kits, are guaranteed to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of 5 years from the date of purchase or up to 50,000 miles, whichever occurs first. All other BAKER products are guaranteed to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of 2 years from the date of purchase or up to 24,000 miles, whichever occurs first, except for the following; Warranty does not cover clutch plate wear, throw out bearing failures or mainshaft breakage due to improper clutch nut installation.Electrical components carry a 30-day warranty; cosmetic finishes (chrome plating, hard anodizing, powder coating) are covered for 60 days. Certain promotional products may carry a shorter warranty as specified at the time of purchase. If the product is found by BAKER to be defective, such products will, at the option of BAKER, be replaced or repaired at cost to BAKER.In the event warranty service is required, the original purchaser must call or write BAKER immediately with a description of the problem. If it is deemed necessary for BAKER to make an evaluation to determine whether the transmission assembly or transmission kit or accessory is defective, the entire transmission assembly, whether originally purchased as an assembly or kit, must be properly packaged and returned prepaid to BAKER with a copy of the original purchase invoice. If after evaluation by BAKER a defect in materials and/or workmanship is found, BAKER will, at their option, repair or replace the defective part of the assembly.

RETURNS AND EXCHANGES

Returns are permitted within 30 days of the delivery date. Any merchandise returned for any reason (exchange, credit or modification) must be accompanied by a Return Goods Authorization (RGA) number or it will be refused. Call BAKER to obtain this number prior to returning goods for any reason. There is a 15% re-stocking fee for all returned items. BAKER is not liable for any shipping.

ADDITIONAL WARRANTY PROVISIONS

NOTE: Limited warranty does not cover labor or other costs or expenses incidental to the repair and or replacement of BAKER products.This warranty does not apply if one or more of the following situations is judged by BAKER to be relevant: BAKER OEM transmissions ; (these are subject to the OEM manufacturers warranty only), Improper installation , accident, modification (including but not limited to use of unauthorized parts, transmission oils or lubricants), racing, high performance application, mishandling, misapplication, neglect (including but not limited to improper maintenance), or improper repair. BAKER shall not be liable for any consequential or incidental damages arising out of or in connection with a BAKER transmission assembly, transmission kit, component or part. Consequential damages shall include without limitation, loss of use, income or profit, or losses sustained as the result of injury (including death) to any person or loss of or damage to property.BAKER transmissions, transmission kits and accessories are designed exclusively for use in American V-Twin motorcycles. BAKER shall have no warranty or liability obligation if BAKER parts are used in any other application.If it is determined that a BAKER product has been disassembled during the warranty period for any reason, this limited warranty will no longer apply unless you were instructed to do so by a BAKER Drivetrain technician for diagnostic purposes.



Speedometer Recalibration Unit
Move your mouse over image to zoom. Click to enlarge.
Customer Reviews
4.5 Based on 35 Reviews
5 ★
83% 
29
4 ★
3% 
1
3 ★
0% 
0
2 ★
6% 
2
1 ★
8% 
3
Customer Photos
Write a Review Ask a Question

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
  • speed
  • bike
  • speedometer
  • unit
  • charm
  • Bert
  • install
  • answer
  • 2002
  • Baker 6
A
08/03/2024
Anonymous
United States United States
  • What model motorcycle do you ride? 2002 Low Rider

Great Product, Won’t Correct All Problems

Will not work on certain bikes, I was able to correct my speedometer up to the 10% limit of the bikes computer system. After about a 10% correct the bike throws a CEL and doesn’t allow Cruise to work. Bike’s programming looks for a certain split between transmission speed and ABS speed, once this threshold is exceeded the bike goes crazy. If your running a higher tooth rear sprocket on a newer HD, this will not solve your problem.

PR
03/04/2024
Peter R.
United States

Repeat customer.

I installed one of these in 2003 on my build with an OD6 speed builders kit. This unit is still in good order on the bike and I still ride it.

PR
03/04/2024
Peter R.
United States United States
  • What model motorcycle do you ride? 2003 FXR Homemade (Chopper Guys)

Repeat customer.

I installed one of these in 2003 on my build with an OD6 speed builders kit. This unit is still in good order on the bike and I still ride it.

MB
06/23/2023
Michael B.
United States United States
  • What model motorcycle do you ride? 2002 softail

A needed extra

Installed a direct drive 6 speed in my wifes 2002 Heritage Softail. We do a lot of long trips and the 6 speed was the answer. Drops rpm in 6th around 700 rpm. But an ubdocumented feature is the need for recalibration. Bought the module had it I stalled in 10 min. Fired up google maps hit 60mph ans recaled speedo on the move in less than 5 min. Matches gps exactly

MB
06/23/2023
Michael B.
United States

A needed extra

Installed a direct drive 6 speed in my wifes 2002 Heritage Softail. We do a lot of long trips and the 6 speed was the answer. Drops rpm in 6th around 700 rpm. But an ubdocumented feature is the need for recalibration. Bought the module had it I stalled in 10 min. Fired up google maps hit 60mph ans recaled speedo on the move in less than 5 min. Matches gps exactly

Web Product ID: 9246009166
Baker Drivetrain Team Illustration

Starting in 1994, the factory started using electronic speedos on some of the models. Today, all models use this. If you are changing the transmission pulley, rear wheel pulley, rear tire or installing one of our transmissions, you will need a recal box. 

  • 95E-56B fits 1987-2006 Big Twin (except 2006 Dyna)
  • 95E-07-A fits 2006-Later Dyna and 2007-Later Softail/Touring models

Instructions for 95E-56B: Click Here

Instructions for 95E-07-A: Click Here

TERMS AND CONDITIONS

BAKER Drivetrain reserves the right to change prices, terms or policies at any time without notice. Orders can be pre-paid using Visa, MasterCard, American Express, Discover or PayPal. All orders not pre-paid will be sent C.O.D. certified check or money order only unless pre-approved for company check acceptance. Any orders from outside the USA must be pre-paid in US funds via wire transfer; a $30 transfer fee will apply. Prices shown are F.O.B. Haslett, MI.

LIMITED WARRANTY POLICY

BAKER™ transmission assemblies and transmission builder 's kits, are guaranteed to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of 5 years from the date of purchase or up to 50,000 miles, whichever occurs first. All other BAKER products are guaranteed to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of 2 years from the date of purchase or up to 24,000 miles, whichever occurs first, except for the following; Warranty does not cover clutch plate wear, throw out bearing failures or mainshaft breakage due to improper clutch nut installation.Electrical components carry a 30-day warranty; cosmetic finishes (chrome plating, hard anodizing, powder coating) are covered for 60 days. Certain promotional products may carry a shorter warranty as specified at the time of purchase. If the product is found by BAKER to be defective, such products will, at the option of BAKER, be replaced or repaired at cost to BAKER.In the event warranty service is required, the original purchaser must call or write BAKER immediately with a description of the problem. If it is deemed necessary for BAKER to make an evaluation to determine whether the transmission assembly or transmission kit or accessory is defective, the entire transmission assembly, whether originally purchased as an assembly or kit, must be properly packaged and returned prepaid to BAKER with a copy of the original purchase invoice. If after evaluation by BAKER a defect in materials and/or workmanship is found, BAKER will, at their option, repair or replace the defective part of the assembly.

RETURNS AND EXCHANGES

Returns are permitted within 30 days of the delivery date. Any merchandise returned for any reason (exchange, credit or modification) must be accompanied by a Return Goods Authorization (RGA) number or it will be refused. Call BAKER to obtain this number prior to returning goods for any reason. There is a 15% re-stocking fee for all returned items. BAKER is not liable for any shipping.

ADDITIONAL WARRANTY PROVISIONS

NOTE: Limited warranty does not cover labor or other costs or expenses incidental to the repair and or replacement of BAKER products.This warranty does not apply if one or more of the following situations is judged by BAKER to be relevant: BAKER OEM transmissions ; (these are subject to the OEM manufacturers warranty only), Improper installation , accident, modification (including but not limited to use of unauthorized parts, transmission oils or lubricants), racing, high performance application, mishandling, misapplication, neglect (including but not limited to improper maintenance), or improper repair. BAKER shall not be liable for any consequential or incidental damages arising out of or in connection with a BAKER transmission assembly, transmission kit, component or part. Consequential damages shall include without limitation, loss of use, income or profit, or losses sustained as the result of injury (including death) to any person or loss of or damage to property.BAKER transmissions, transmission kits and accessories are designed exclusively for use in American V-Twin motorcycles. BAKER shall have no warranty or liability obligation if BAKER parts are used in any other application.If it is determined that a BAKER product has been disassembled during the warranty period for any reason, this limited warranty will no longer apply unless you were instructed to do so by a BAKER Drivetrain technician for diagnostic purposes.